Date: November 16 , 2004 Subject: Storage Procedure (2-strokeengine units)No. 2004-19YEAR MODEL MODEL NUMBER SERIAL NUMBER3D™ RFI 6157/6158GTI™ / GTI
F17E0AB1NNNNOOOOTTTTEEEE:::: On RFI models, make sure the hose [[[[1]]]]isproperly connected to the magneto cover.F17E03A1Install a hose pincher on in
F17E01A1Photo shows engine water outlet hose [[[[1]]]], 717and 787 RFI engines.F06E0EB1Hose DisconnectionSome hoses have to be disconnected. Disconnec
F15E02A21Model(s): 787 RFI EnginesDisconnect hose [[[[2]]]] just above T-fitting [[[[1]]]]as shown.F15E03A1Install a hose pincher [[[[1]]]] just below
Model(s): 3DEngine and Tuned PipeNNNNOOOOTTTTEEEE:::: This procedure requires approximately 2.5 L(2.6 U.S. qt) of antifreeze.Remove rear access panel
F07E0LATYPICALF22L0HA1Insert a funnel into the temporary hose and pourantifreeze in engine until the colored solutionappears at the cooling system ble
Complete Cooling SystemNNNNOOOOTTTTEEEE:::: For the above engine and exhaust systemprocedures, although antifreeze will mainly drainout, it has mixed
F08E0PA1Photo shows water outlet hose [[[[1]]]] underneathtuned pipe.F08E0SA1Hose DisconnectionDisconnect the bottom hose [[[[1]]]]atthewaterregulator
F08E0TAAAntifreezeInsert a funnel into the temporary hose. Ensure tohold the funnel approximately 1 m (3 ft) [[[[A]]]]abovethedeckwhenpouringtheantifr
F08E0JA1Continue to pour until antifreeze appears at theengine drain hose [[[[1]]]] (crankcase cooling outlet).Then, install a hose pincher on this ho
NNNNOOOOTTTTEEEE:::: Although antifreeze will mainly drain out,the antifreeze has mixed with the water that waspossibly trapped in the water jackets a
F17E0AA1Model(s): RFIDisconnect the water supply hose used to cool themagneto. It features a quick connect fitting. Pressboth tabs [[[[1]]]] and pull
CHECK LISTOOOOPPPPEEEERRRRAAAATTTTIIIIOOOONNNN✔✔✔✔Check engine drain hose(s).Drain and clean impeller shaft reservoir.Lubricate PTO flywheel or seal c
12F17E0BAWater should flow out of the fitting [[[[1]]]] (magnetocooling circuit) and hose [[[[2]]]] (crankcase heatexchanger).Push and hold hose again
PROPULSION SYSTEMModel(s): AllJet PumpLubricant in impeller shaft reservoir should bedrained. Reservoir should be cleaned and refilledwith SEA-DOO syn
Seal CarrierModel(s): XP DI and 3DF08E0BA1Lubricate seal carrier [[[[1]]]] of driveshaft support withsynthetic grease. Stop lubricating when greasesta
WARNINGFuel is flammable and explosive under certainconditions. Always work in a well ventilatedarea. Do not smoke or allow open flamesor sparks in t
BATTERYModel(s): AllFor battery removal, cleaning and storage, refer toCHARGING SYSTEM in Shop Manual.Model(s): 3D RFIRefer to STORAGE in Shop Manual
ADDITIONALRECOMMENDEDPROTECTIONModel(s): AllIn cool regions (where freezing point may beencountered), cooling system should be filled withpure undilut
1F17E05AInstall hose pinchers where indicated.Photo shows engine drain hose [[[[1]]]]onGTIandGTILE models, 717 engine.F15E01A1Install hose pinchers wh
Kommentare zu diesen Handbüchern